/* USER CODE BEGIN Header */
|
/**
|
******************************************************************************
|
* @file gpio.c
|
* @brief This file provides code for the configuration
|
* of all used GPIO pins.
|
******************************************************************************
|
* @attention
|
*
|
* Copyright (c) 2022 STMicroelectronics.
|
* All rights reserved.
|
*
|
* This software is licensed under terms that can be found in the LICENSE file
|
* in the root directory of this software component.
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
*
|
******************************************************************************
|
*/
|
/* USER CODE END Header */
|
|
/* Includes ------------------------------------------------------------------*/
|
#include "gpio.h"
|
|
/* USER CODE BEGIN 0 */
|
|
/* USER CODE END 0 */
|
|
/*----------------------------------------------------------------------------*/
|
/* Configure GPIO */
|
/*----------------------------------------------------------------------------*/
|
/* USER CODE BEGIN 1 */
|
|
/* USER CODE END 1 */
|
|
/** Configure pins as
|
* Analog
|
* Input
|
* Output
|
* EVENT_OUT
|
* EXTI
|
* Free pins are configured automatically as Analog (this feature is enabled through
|
* the Code Generation settings)
|
*/
|
void MX_GPIO_Init(void)
|
{
|
|
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|
/* GPIO Ports Clock Enable */
|
__HAL_RCC_GPIOC_CLK_ENABLE();
|
__HAL_RCC_GPIOH_CLK_ENABLE();
|
__HAL_RCC_GPIOA_CLK_ENABLE();
|
__HAL_RCC_GPIOB_CLK_ENABLE();
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(GPIOA, EXT_END_Pin|RET_END_Pin|SENSOR_EN_Pin|ALARM_C_Pin, GPIO_PIN_RESET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(GPIOB, POWER_MCU2_Pin|CAN_STB_Pin|DRV_L_EN_Pin, GPIO_PIN_RESET);
|
|
/*Configure GPIO pins : PC13 PC14 */
|
GPIO_InitStruct.Pin = GPIO_PIN_13|GPIO_PIN_14;
|
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
|
/*Configure GPIO pin : PtPin */
|
GPIO_InitStruct.Pin = CAN_DET_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
HAL_GPIO_Init(CAN_DET_GPIO_Port, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PAPin PAPin PAPin PAPin */
|
GPIO_InitStruct.Pin = EXT_END_Pin|RET_END_Pin|SENSOR_EN_Pin|ALARM_C_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PAPin PAPin */
|
GPIO_InitStruct.Pin = INCSIM_A_Pin|INCSIM_B_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PBPin PBPin PBPin */
|
GPIO_InitStruct.Pin = POWER_MCU2_Pin|CAN_STB_Pin|DRV_L_EN_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PBPin PBPin PBPin PBPin */
|
GPIO_InitStruct.Pin = EXTEND_IN_Pin|RETRACT_IN_Pin|DIAG_M1_Pin|DIAG_M2_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PA10 PA11 PA12 PA15 */
|
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12|GPIO_PIN_15;
|
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
/*Configure GPIO pin : PH3 */
|
GPIO_InitStruct.Pin = GPIO_PIN_3;
|
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
|
|
}
|
|
/* USER CODE BEGIN 2 */
|
|
/* USER CODE END 2 */
|
